No products were found matching your selection.
Other Related Products
-
Double sided acrylic tape shear strength describes resistance to a sustained load acting parallel to bonded surfaces. The value is meaningful only when bonded area, load, substrate, temperature, application pressure, dwell time, and failure criterion are stated. It explains static shear holding, how it differs from peel and tack, and when results are not comparable. Typical values and reference ranges should be confirmed by sample testing.
-
- Common thickness: 0.2 mm-5.0 mm
- Color: black, white, gray, or custom
- Carrier: PE foam, PU foam, EPDM, neoprene, or rubber
- Adhesive: acrylic PSA, rubber PSA, or differential PSA
- Liner: paper, PET, glassine, coated paper, or dual liner
- Supply form: rolls, sheets, kiss-cut parts, or die-cut gaskets
-
- Standard widths: 10mm, 15mm, 20mm, 25mm
- Color: Transparent
- Carrier material: Thin PET film (25 u)
- Adhesive type: Skin-safe acrylic layer, 80 u
- Application: Temporary fabric-to-fabric or fabric-to-skin fixing
- Peel adhesion: 0.8–1.2 N/cm (fabric-to-fabric), 0.5–0.9 N/cm (fabric-to-skin)
-
- Common thickness: 1/8 inch, 1/4 inch, 3/8 inch, 1/2 inch, 3/4 inch, 1 inch
- Color: gray, charcoal gray, or custom dark foam appearance
- Material: open-cell polyether urethane foam
- Adhesive option: rubber PSA, acrylic PSA, single sided, double sided, or plain foam
- Supply form: slit rolls, sheets, kiss-cut pads, and die-cut parts
- Main use: cushioning, gasketing, sound damping, light blocking, and vibration control
-
- Width: 90 mm / 100 mm
- Length: 20 m / 50 m
- Color: Yellow, white, gold
- Adhesive: Heat activated hot melt
- Placement: Below carpet joint
- Use: Heat iron joining
-
- Material: Transparent PU gel adhesive
- Color: Clear, high transparency
- Thickness: 0.5 mm, 1.0 mm, 2.0 mm, 3.0 mm
- Format: Roll, pad, strip, gasket
- Width: 10 mm-500 mm or slit to size
- Processing: Slitting, die cutting, kiss cutting
-
Double sided tape for artificial grass can support turf-to-turf seaming, patch repair, light perimeter support and temporary turf-to-floor fixing, but these jobs create different bond lines. Selection should start with the actual turf backing, substrate, exposure, traffic and removal requirement rather than hand tack alone. Main risks include visible joints, edge lift, contaminated or damp contact surfaces, movement before adequate contact develops and adhesive transfer during removal. Where the surface, coating or outdoor condition is uncertain, a representative sample seam should be tested before full use.
-
- Material: Closed-cell PE foam carrier
- Thickness: 0.5 mm-3.0 mm typical
- Density: 45-100 kg/m3 typical
- Color: White, black, gray optional
- Adhesive: Rubber, acrylic, solvent acrylic PSA
- Processing: Slitting, die-cutting, warm pressing, laminating
-
- Common thickness: 0.4 mm, 0.6 mm, 0.8 mm, 1.0 mm, 1.2 mm, 1.5 mm
- Color: black, gray, white, or custom foam color
- Foam carrier: closed-cell PE foam or acrylic foam option
- Adhesive: automotive-grade acrylic pressure-sensitive adhesive
- Liner: red PE film, white paper, or easy-release film liner
- Typical tolerance: +/-05 mm thickness, +/-0.5 mm slitting reference
