No products were found matching your selection.
Other Related Products
-
- Common thickness: 1/8 inch, 1/4 inch, 3/8 inch, 1/2 inch, 3/4 inch, 1 inch
- Color: gray, charcoal gray, or custom dark foam appearance
- Material: open-cell polyether urethane foam
- Adhesive option: rubber PSA, acrylic PSA, single sided, double sided, or plain foam
- Supply form: slit rolls, sheets, kiss-cut pads, and die-cut parts
- Main use: cushioning, gasketing, sound damping, light blocking, and vibration control
-
Closed cell EPDM foam properties are commonly compared through compression deflection, compression set, density, tensile strength, elongation, water absorption, and resistance to temperature, ozone, and weather. These values help screen grades for sealing, gasketing, cushioning, and adhesive-backed constructions. Read results with the stated test method and specimen condition, then confirm suitability on the intended surface, compression level, adhesive construction, and service environment.
-
- Material: Closed-cell neoprene foam
- Color: Black as standard
- Adhesive: Rubber PSA or acrylic PSA
- Liner: Kraft paper or PE-coated release liner
- Thickness: 1 mm-20 mm common range
- Format: Slit rolls, die-cut gaskets, kiss-cut parts
-
- Material: Cross-linked PE foam carrier
- Foam Type: IXPE foam with fine closed-cell structure
- Thickness: 0.5 mm-10 mm typical options
- Density: 25-100 kg/m3 for different compression needs
- Color: Black, white, grey
- Use: Gasket, spacer, sealing, cushioning, die-cut parts
-
Double sided tape for artificial grass can support turf-to-turf seaming, patch repair, light perimeter support and temporary turf-to-floor fixing, but these jobs create different bond lines. Selection should start with the actual turf backing, substrate, exposure, traffic and removal requirement rather than hand tack alone. Main risks include visible joints, edge lift, contaminated or damp contact surfaces, movement before adequate contact develops and adhesive transfer during removal. Where the surface, coating or outdoor condition is uncertain, a representative sample seam should be tested before full use.
-
- Common thickness: 0.2 mm-5.0 mm
- Color: black, white, gray, or custom
- Carrier: PE foam, PU foam, EPDM, neoprene, or rubber
- Adhesive: acrylic PSA, rubber PSA, or differential PSA
- Liner: paper, PET, glassine, coated paper, or dual liner
- Supply form: rolls, sheets, kiss-cut parts, or die-cut gaskets
-
- Standard widths: 10mm, 15mm, 20mm, 25mm
- Color: Transparent
- Carrier material: Thin PET film (25 u)
- Adhesive type: Skin-safe acrylic layer, 80 u
- Application: Temporary fabric-to-fabric or fabric-to-skin fixing
- Peel adhesion: 0.8–1.2 N/cm (fabric-to-fabric), 0.5–0.9 N/cm (fabric-to-skin)
-
- Material: PET/polyester film carrier with acrylic adhesive on both sides
- Color: Clear, translucent, black, or custom tinted film
- Thickness: 0.03 mm to 0.20 mm typical range
- Liner: Glassine paper, PE-coated paper, PET film, or double liner
- Format: Jumbo roll, slit roll, sheet, kiss-cut, or die-cut part
- Use: Nameplates, panels, overlays, membrane switches, and electronics
-
- Width: 10 mm-50 mm
- Thickness: 1 mm-5 mm
- Color: Black, grey, custom
- Backing: Heat resistant fiber composite
- Adhesive: High temperature self adhesive backing
- Use Area: Lid edge, door gap, window edge
