No products were found matching your selection.
Other Related Products
-
- Common size: 2-20 mm thickness, custom slit width
- Color: Black EPDM foam with protected adhesive side
- Material: Closed-cell EPDM foam carrier
- Adhesive: One-sided pressure sensitive backing
- Liner: Peel-off paper or film release liner
- Use: Sealing, cushioning, gap filling
-
- Material: Cross-linked PE foam carrier
- Foam Type: IXPE foam with fine closed-cell structure
- Thickness: 0.5 mm-10 mm typical options
- Density: 25-100 kg/m3 for different compression needs
- Color: Black, white, grey
- Use: Gasket, spacer, sealing, cushioning, die-cut parts
-
Double sided acrylic tape shear strength describes resistance to a sustained load acting parallel to bonded surfaces. The value is meaningful only when bonded area, load, substrate, temperature, application pressure, dwell time, and failure criterion are stated. It explains static shear holding, how it differs from peel and tack, and when results are not comparable. Typical values and reference ranges should be confirmed by sample testing.
-
- Material: PET/polyester film carrier with acrylic adhesive on both sides
- Color: Clear, translucent, black, or custom tinted film
- Thickness: 0.03 mm to 0.20 mm typical range
- Liner: Glassine paper, PE-coated paper, PET film, or double liner
- Format: Jumbo roll, slit roll, sheet, kiss-cut, or die-cut part
- Use: Nameplates, panels, overlays, membrane switches, and electronics
-
- Common Size: jumbo rolls, slit rolls, die-cut pads, strips, and laminated sheets.
- Color: white, black, grey, or custom foam color.
- Material: PE, EVA, IXPE, or PU foam carrier.
- Adhesive: acrylic, rubber, or hot melt PSA on both sides.
- Thickness: 0.3 mm to 3.0 mm typical range.
- Use: panel bonding, nameplate mounting, molding fixing, and converter processing.
-
- Common thickness: 1/8 inch, 1/4 inch, 3/8 inch, 1/2 inch, 3/4 inch, 1 inch
- Color: gray, charcoal gray, or custom dark foam appearance
- Material: open-cell polyether urethane foam
- Adhesive option: rubber PSA, acrylic PSA, single sided, double sided, or plain foam
- Supply form: slit rolls, sheets, kiss-cut pads, and die-cut parts
- Main use: cushioning, gasketing, sound damping, light blocking, and vibration control
-
- Common thickness: 0.4 mm, 0.6 mm, 0.8 mm, 1.0 mm, 1.2 mm, 1.5 mm
- Color: black, gray, white, or custom foam color
- Foam carrier: closed-cell PE foam or acrylic foam option
- Adhesive: automotive-grade acrylic pressure-sensitive adhesive
- Liner: red PE film, white paper, or easy-release film liner
- Typical tolerance: +/-05 mm thickness, +/-0.5 mm slitting reference
-
Double sided tape for artificial grass can support turf-to-turf seaming, patch repair, light perimeter support and temporary turf-to-floor fixing, but these jobs create different bond lines. Selection should start with the actual turf backing, substrate, exposure, traffic and removal requirement rather than hand tack alone. Main risks include visible joints, edge lift, contaminated or damp contact surfaces, movement before adequate contact develops and adhesive transfer during removal. Where the surface, coating or outdoor condition is uncertain, a representative sample seam should be tested before full use.
-
- Material: Closed-cell neoprene foam
- Color: Black as standard
- Adhesive: Rubber PSA or acrylic PSA
- Liner: Kraft paper or PE-coated release liner
- Thickness: 1 mm-20 mm common range
- Format: Slit rolls, die-cut gaskets, kiss-cut parts
